特別是輸出輥道，過去多采用上述方法對中，但是近有把輥距縮小的傾向，因而采用后一種斜輥布置方式的輥道正在減少。這是為了在軋制薄規格的帶鋼時避免使帶鋼在輥道上因終軋速度高而造成折疊。此外，對于輥道的速度和輥?zhàn)又睆揭惨浞挚紤]好。

In particular, the output roller table used to use the above methods in the past, but recently there is a tendency to narrow the distance between rolls. Therefore, the roller table with the latter one is decreasing. to avoid folding the strip on a thin strip of strip to avoid the high finishing speed of the strip on the roller. In addition, the speed of the roller and the diameter of the roller should be fully cidered.

為使鑄坯平穩迅速地運送，有時將這個區的輥道設計成可升降的。輥道按驅動方式可分為集中傳動輥道和單獨傳動輥道兩種。集中傳動輥道由一臺電機帶動一組輥?zhàn)樱ㄟ^電機一減速機一鏈輪傳動，或者通過電機一減速機～長軸一傘齒輪傳動方式傳動。

In order to deliver the billet smoothly and quickly, the roller table in this area is sometimes designed to be lifted and lifted. The roller table can be divided into two types: the  drive roller and the separate drive roller. The  driven roller table is driven by a motor to a set of rollers, driven by a motor, a reducer or a sprocket, or through a motor, a reducer, a long shaft and a bevel gear transmission mode.

單獨傳動輥道為一個電機帶動一個輥?zhàn)?。這種輥道結構簡單，操縱靈活，維修方便。根據鑄坯的斷面尺寸計算選擇輥?zhàn)又睆胶洼伾黹L(zhǎng)度，切割區后的輥道輥間距取決于定尺長度。為使軋件能夠在輥道中心運行，采用鼓形輥，并且交替地使左右兩邊的水平面稍微傾斜，或者使輥?zhàn)拥妮S線與軋件運行方向的交角交替地比直角稍微偏斜一些。切割前輥道速度與拉坯速度一致，切割后要迅速輸送鑄坯，輥道速度一般為20～30m/min。

A single drive roller is used as a motor to drive a roller. The roller table is simple in structure, flexible in operation and convenient in maintenance. According to the section size of the slab, the diameter of the roller and the length of the roller are calculated. The roller spacing after the cutting area depends on the length of the length. Before cutting roller speed and casting speed, after cutting to quickly transfer slab, roller speed is 20 ~ 30m/min.

包膠滾筒的壽命是比較長的，像這種要求就是要壽命長的，因?yàn)榘跐L筒上邊也不是很方便取下來呀，所以這就又驗證一點.

The life of the rubber drum is long, and the requirement is long life, because it is not very convenient to take the package on the top of the drum, so this will verify the first point again.