在運轉200~300小時后，應進行換油，在以后的使用中應定期檢查油的質量，對于混入雜質或變質的油須及時更換。一般情況下，對于長期連續工作的減速機，按運行5000小時或每年一次更換新油.

After running for 200~300 hours, the first oil change should be done. The quality of the oil should be checked regularly in later use, and the oil mixed with impurities or deterioration must be changed in time. In general, for a long-term continuous working reducer, new oil is replaced at 5000 hours or once a year.

在減速機家族中，行星減速機以其體積小，減速范圍廣，精度高等諸多有點，而被應用于伺服、步進、直流等傳動系統中。其作用就是在保證精密傳動下，主要被用來降低轉速增大扭矩和降低負載/電機的轉動慣量比。

In reducer family, planetary reducer is applied to servo, step and DC transmission systems because of its small volume, wide range of deceleration and high accuracy. Its role is to ensure the precision drive, mainly used to reduce the rotational speed to increase the torque and reduce the load / motor inertia ratio.

允許輸入法蘭：

不能大于或小于臨級減速機的標準尺寸，如減速機PLE80?的標準法蘭為80mm,其臨級的減速級是PLE60?和PLE120，PLE80?允許法蘭不應小于60mm,也不能大于120mm。

Allow input flange

It can't be greater than or less than the standard  of the reducer. For example, the standard flange of reducer PLE80 is 80mm, and the deceleration stage of its reducer is PLE60?3,使用特殊的寬帶寬壓力電動機,當加載在20hz-60赫茲頻率范圍內正常使用。 PLE120, PLE80? The maximum allowable flange should not be less than 60mm, nor greater than 120mm.

通常齒輪減速機已廣泛應用于冶金、礦山、起重、運輸、水泥、建筑、化工、紡織、印染、制藥、等領域。但在這種齒輪減速機的使用有一定的限制,所以,讓我們了解下使用時需要注意什么。

1、高速旋轉不超過1500 r / min。齒輪減速器。

2、齒輪圓周速度不超過20 m / s。

Usually gear reducer has been widely used in metallurgy, mining, lifting, transportation, cement, ctruction, chemical, textile, printing and dyeing, pharmaceutical, and other fields. But there are some restricti on the use of this gear reducer, so let us know what to pay attention to when using it.

1. The high speed rotation does not exceed 1500 R / min. Gear reducer.

2, the circumferential speed of the gear is not more than 20 m / S.