彎曲度：工字鋼高度小于或等于400MM時，每米彎曲度不得大于1.5MM，總彎曲度不得大于總長度的0.15%。高度大于400MM時，每米彎曲度不得大于1.0MM，總彎曲度不得大于總長度的0.1%。

Bending degree: when the height of the I-steel is less than or equal to 400MM, the bending degree of each meter must not be more than 1.5MM, and the total bending degree should not be more than 0.15% of the total length. When the height is greater than 400MM, the bending degree of each meter must not be more than 1.0MM, and the total bending degree should not be more than 0.1% of the total length.

型材是鐵或鋼以及具有一定強度和韌性的材料通過軋制、擠出、鑄造等工藝制成的具有一定幾何形狀的物體。這類材料具有的外觀尺寸一定，斷面呈一定形狀，具有一定的力學物理性能。型材既能單獨使用也能進一步加工成其他制造品，常用于建筑結構與制造安裝。型材的材質、規格尺寸等可參照相應的國家標準。com/item/裝飾板材/3943836。軋機結構和軋機布置形式較多。在結構形式上有二輥式軋機、三輥式軋機、孔型軋機、多輥孔型軋機、Y型軋機、45°軋機和懸臂式軋機等。

型材按使用部門分類有鐵路用型材（鋼軌、魚尾板、道岔用軌、車輪、輪箍）、汽車用型材（輪輞、輪胎擋圈和鎖圈）、造船用型材（L型鋼、球扁鋼、Z字鋼、船用窗框鋼）、結構和建筑用型材（H型鋼、工字鋼、槽鋼、角鋼、吊車鋼軌、窗框和門框用材、鋼板樁等）、礦山用鋼（U型鋼、槽幫鋼、礦用工字鋼、刮板鋼等）、機械制造用異型材等。按斷面尺寸大小分類。5~10毫米）Thesteelofathicksteelplateisroughlythesameasthatofathinsteelplate。

有的膠合板是將兩個不同紋路的單板貼在一起制成的，所以在選擇上要注意夾板拼縫處應嚴密，沒有高低不平現象。挑選膠合板時，應注意挑選不散膠的膠合板。如果手敲膠合板各部位時，聲音發脆，則證明質量良好，若聲音發悶，則表示膠合板已出現散膠現象。

Some plywood plywood is made of two different lines of the single board together, so in the choice of the splints should be careful to pay attention to the joint, there is no uneven phenomenon. When choosing plywood, you should pay attention to selecting plywood without glue. If the hand knocks on the plywood parts, the sound is crisp, which proves that the quality is good. If the voice is stuffy, it means that the plywood has already appeared loose glue phenomenon.