混流泵

開車順序：

    1、關閉出口閘閥

    2、將水注入水泵，以排除進水管及泵內空氣，可從泵體頂端引水杯注入清水，也可用真空泵注水（開動真空泵，排除水泵及管內氣體在水充滿水泵的同時，起動水泵，打開閘閥，停止真空泵）。

3、開啟電動機（注意水泵的旋轉方向）。

    4、當電動機正常運轉后，逐步開大閘閥，達到所要求的工況后，調節填料松緊。若水泵運轉，軸承溫度等都正常，則可繼續運行。

III.  Starting

Sequence

   1.Close the oulet

sluice valve.

   2. Inject

water into pump to remove the air in water-in pipe and pump which can realized

by injecting clear water from the water diversion cup of the pump body end or

by vacuum pump(start the vacuum pump, remove the air from pump and pipes, start

the water pump when the pump is full of water, open the sluice valve, stop the

vacuum pump).

   3. Start the

motor(pay more attention on the rotation direction of pump)

   4. When the motor runs normally, turn up the

sluice valve gradually, adjust the tightness of padding when gettng to the

required working condition.If the pump runs well, the temperature of bearing is

normal, and it can run sequentially.

 6、軸承發熱

 The bearing is

 hot

 1、潤滑油脂不足

 2、潤滑油質量不好或不清潔

 3、軸心沒有對準

 4、軸承松動或磨損

 5、皮帶太緊

 1.Lubricating grease is not enough

 2.The quality of lubricating oil is not

 good or dirty

 3.The axes is not aiming

 4.The bearing is loose or attrition

 5.The belt is too tight.

 1、加油

 2、清洗軸承

 3、找正

 4、修正

 5、適當放松

 1.Add lubrication oil

 2.Wash

 the bearing

 3.Aligning

 4.Amending

 5.Loosen it properly

按行業分類石油泵、冶金泵、化工泵、漁業泵、礦業泵、電力泵、水利泵、水處理泵、食品泵、釀造泵、制藥泵、飲料泵、煉油泵、調料泵、造紙泵、紡織泵、印染泵、制陶泵、油漆泵、 、化肥泵、制糖泵、酒精泵、環保泵、制鹽泵、啤酒泵、淀粉泵、供水泵、供暖泵、農用泵、園林泵、水族泵、鍋爐泵、泵、船舶泵、航空泵、汽車泵、消防泵、水泥泵、空調泵、泵、機械泵、燃?xì)獗?、油氣混輸?img src="https://pic.etlong.com/202007/23/091457648619353.jpg" />