【廣告】
混流泵
3.
Installation base:The soil texture should be firm and solid.
4.
During installation, keep the pump axile in horizontal p ition.
5.The end of
water inlet pipe should be immersed under water in about one meter and far away
from the end of mud in about half meter.
6.After installing the pump,calculate the
suitable suction height and head.Under the stable water level condition,
5、水泵有雜音或振動
There is noise
in pump or the pump is vibrating
1、軸中心沒有對正
2、軸彎曲軸承磨損過大
3、葉輪平衡性差
4、地腳螺栓松動
5、裝置不當
6、葉輪局部阻塞
7、吸水高度太高、發生汽蝕
8、泵內掉進雜物
1.The axile center is not aligning
2.The axile is bend, the bearing wears
much
3.The balance of impeller is not good
4.The foundation bolts are loose
5.The assembly is improper
6.Part of the impeller is blocked
7.The suction head is too high to produce
cavitation
8.There are sundries in pump.
1、找正
2、校正或更換軸承
3、進行靜平衡試驗和調整
4、擰緊
5、檢查機組
6、消除雜物
7、降低安裝位置減低安裝高度
8、清除雜物
1.Calibrate
2.Calibrate it or change the bearing
3.Do the static balancing test and adjust
it
4.Tighten it
5.Check the pump unit
6.Remove the sundries
7.Reduce the installation site to reduce
the installation height
8. Remove the sundries
4. 水泵的安裝位置應滿足允許吸上真空高度的要求,基礎必須水平、穩固,保證動力機械的旋轉方向與水泵的旋轉方向一致。
5. 若同一機房?jī)?nèi)有多臺機組,機組與機組之間,機組與墻壁之間都應有800mm以上的距離。
6. 水泵吸水管必須密封良好,且盡量減少?gòu)濐^和閘閥,加注引水時應排盡空氣,運行時管內不應積聚空氣,要求吸水管微呈上斜與水泵進水口聯接,進水口應有一定的淹沒深度。
深井潛水泵
首先看一下水泵此時運行的電流和平常運行時候的電流差別有多大。如果比平時運行時候小(基上就是平時電流的23),那么就有葉輪磨損、泵頭上面的止逆閥堵塞等問題。缺相運行,經驗表明農用電動機被燒毀85%以上是由于缺相運行造成的,應對電動機安裝缺相保護裝置。如果和平時電流一樣大,那么就是管墊漏水、管子漏水、泵體漏水等問題。如果比平時運行的時候電流大,那么基上可以確定是易損件磨損的問題。另外補充一點,電纜如果破損的話,水量跟平時是一樣大,但是電流會變大。3相380V電機的電流一般是2.2A。以上原因只要是經常維修深井泵的修理人員就可以查出來。