混流泵

開車順序：

    1、關閉出口閘閥

    2、將水注入水泵，以排除進水管及泵內空氣，可從泵體頂端引水杯注入清水，也可用真空泵注水（開動真空泵，排除水泵及管內氣體在水充滿水泵的同時，起動水泵，打開閘閥，停止真空泵）。

3、開啟電動機（注意水泵的旋轉方向）。

    4、當電動機正常運轉后，逐步開大閘閥，達到所要求的工況后，調節填料松緊。若水泵運轉，軸承溫度等都正常，則可繼續運行。

III.  Starting

Sequence

   1.Close the oulet

sluice valve.

   2. Inject

water into pump to remove the air in water-in pipe and pump which can realized

by injecting clear water from the water diversion cup of the pump body end or

by vacuum pump(start the vacuum pump, remove the air from pump and pipes, start

the water pump when the pump is full of water, open the sluice valve, stop the

vacuum pump).

   3. Start the

motor(pay more attention on the rotation direction of pump)

   4. When the motor runs normally, turn up the

sluice valve gradually, adjust the tightness of padding when gettng to the

required working condition.If the pump runs well, the temperature of bearing is

normal, and it can run sequentially.

4、注意填料的冷卻情況，填料的的調整，不可太緊，以液體能一滴一滴漏出為準，填料太緊發熱、消耗功率。填料太松、使水泵中的液體漏損過多，降低效率。

Pay more

attention to the cooling condition of padding.The padding can not be too tight,

it is ok that the fluid can leak in drops.The temperature will be high if the

padding is too tight which cumes power.If the padding is too loose, the

fluid leaks too much, the efficiency will be lower.

水泵發熱

原因：軸承損壞；滾動軸承或托架蓋間隙過?。槐幂S彎曲或兩軸不同心；膠帶太緊；缺油或油質不好；葉輪上的平衡孔堵塞，葉輪失去平衡，增大了向一邊的推力。排除方法：更換軸承；拆除后蓋，在托架與軸承座之間加裝墊片；調查泵軸或調整兩軸的同心度；適當調松膠帶緊度；加注干凈的黃油，黃油占軸承內空隙的60%左右；其特點是，與混流泵、軸流泵相比，揚程較高，流量較小，結構簡單，使用方便。清除平衡孔內的堵塞物。

劇烈震動

主要有以下幾個原因：電動轉子不平衡；聯軸器結合不良；軸承磨損彎曲；轉動部分的零件松動、；管路支架不牢等原因?？煞謩e采取調整、修理、加固、校直、更換等辦法處理。