精整，是軋鋼生產過程中后一個工序，也是較為復雜的一個工序。他對產品的質量起著終的保證作用。產品的技術要求不同，精整工序的內容也不大相同。精整的工序通常又包括鋼材的卷取，軋后冷卻，矯直，成品熱處理，成品表面清理以及各種涂色等許多具體工序。

Finishing is the last process in the steel rolling process, and it is also a more complicated process. He has a final guarantee of the quality of the product. The technical requirements of the product are different, and the content of the finishing process is not the same. The finishing process usually includes steel coiling, cooling, straightening products, heat treatment, surface cleaning products and various color and many other specific processes.

軋制變形制度：即一定軋制條件下從坯料到成品的總變形量和軋制的總道次，各機組的總變形量各道次的變形量，軋制方式等。對于型鋼，軋件在孔型中軋制，并且在每個孔型中軋制一道，因此，型鋼的變形制度是以孔型的形式表示的，孔型的設計確定后變形制度就確定了。(2)reducethetwooxidationlossonthesurfaceoftheproduct。

Rolling system: that under certain rolling condition the total deformation from the blank to the finished product and the total rolling pass, deformation of the total deformation of each unit of each pass, rolling etc.. For the section steel, the rolled piece is rolled in the pass and rolled in one pass. Therefore, the deformation system of the section steel is expressed in the form of pass, and the deformation system is determined after the pass design is determined.

縱軋是縱向軋制的簡稱，是被軋物體通過兩個反向轉動的軋輥得到加工的軋制方法，軋制時軋件通過輥面間縫隙向前運動，其運動方向與軋輥軸線垂直。縱軋是軋制中常見的一種軋制方法，橫軋是軋件圍繞自身中心線在軋輥間旋轉，并且軋件旋轉中心線與軋輥軸線平行，軋件只在橫向受到壓力加工的一種軋制的方法。Finishingisthelastprocessinthesteelrollingprocess,anditisalsoamorecomplicatedprocess。

Longitudinal rolling is the abbreviation of longitudinal rolling. It is the rolling method of rolled object through two reversing rolls. When rolling, the workpiece moves forward through the gap between the rolls, and its direction of motion is perpendicular to the axis of the roller. Longitudinal rolling is the most common rolling method in rolling. Cross rolling is a rolling method for rolling pieces that rotate around the center line between the rolls, and the  axis of the rolling piece is parallel to the axis of the rolls. The rolling piece is only subjected to pressure on the transverse side.

軋輥的彈性壓扁沿輥身長度散布是不勻稱的，若邊部延伸率大。軋機支持輥的外貌肖氏硬度1樣平常為HS45左右，在另1側設專人觀察，也會出現相反的環境，薄鋼板通常以卷板和剪切成肯定長度和寬度的單張板投放市場。

The elastic flattening of the roll is uneven along the length of the roller body, and the elongation at the side is large. The appearance of the rolling mill support roll is about 1 HS45, which is normally observed on the other 1 sides, and the  environment will occur. Thin plates are usually put on the market with rolled plates and a single sheet that is cut to a certain length and width.