【廣告】
8、填料處漏水太多
The padding is
leaking water too much
1、填料壓得太松
2、填料裝置不好
3、填料大小不一或磨損過多
4、填料質量差,不銹鋼混流泵銷售,密封性不好
5、軸套磨損太多
1.The padding is pressed too loose
2.The padding does not assemble well
3.The padding is not of niform size or it
wears too much
4.The padding is with bad quality and
tightness
5.
1、上緊壓蓋到適應程度
2、調整填料搭口,使之錯開一定角度而不在一個方向
3、更換填料
4、更換符合要求的石棉填料
5、更換軸套
1.Tighten the gland up to suitable degree
2.Adjust the padding jiont up to some
angle not in the same direction.
3.Change the padding
4.Change the suitable asbestos padding
5.Change the axle sleeve.
不同用途
水泵具有不同的用途,不銹鋼混流泵安裝,不同的輸送液體介質,不同的流量、 不同揚程的范圍,因此,它的結構形式當然也不一樣,六盤水市混流泵,材料也不同,概括起來,大致可以分為:
1 、城市供水 2 、污水系統 3 、土木、建筑系統 4 、農業水利系統 5 、電站系統
6 、化工系統 7 、石油工業系統 8 、礦山冶金系統 9 、輕工業系統 10 、船舶系統往復泵、柱塞泵、活塞泵、隔膜泵、轉子泵、螺桿泵、液環泵、齒輪泵、滑片泵、羅茨泵、滾柱泵、凸輪泵、蠕動泵、擾性泵、葉片泵、離心泵、軸流泵、混流泵、漩渦泵、射流泵、噴射泵、水錘泵、真空泵、旋殼泵、軟管泵、蝸桿泵
3、水泵出水量不足
The waer yield
of water is not enough
1、進水管路或葉輪有水草雜物
2、轉速過低
3、輸水高度過高
4、泵蓋及葉輪磨損間隙過大
5、填料進氣
6、馬力不足
7、進水管口插入水中深度不夠
1. There are waterweeds and sundries in
inlet pipes or impeller
2.The rotate speed is too low
3.Water delivery height is too high
4.The attrition gap between pump cover
and impeller is too large
5.The padding is air in
6.The horsepower is not engough
7.The depth of inlet pipe under water is
not enough
1、清除水草雜物
2、調整轉數
3、降低輸水高度
4、用紙墊調整間隙至正常
5、壓緊或更換填料
6、加大馬力
7、增加插入水中深度至一米左右
1.Clear the waterweeds and sundries
2.Ajust the rotate speed
3.Reduce the water delivery height
4.Add paper washers to adjust the gaps
5.Compact or change padding
6.Increase the horsepower
7.Make the depth of inlet pipe under
water to one meter
企業: 泰安金石泵業有限公司
手機: 13605386905
電話: 0538-6202947
地址: 山東省泰安市泰山區南關路12號