【廣告】
開車順序:
1、關閉出口閘閥
2、將水注入水泵,以排除進水管及泵內空氣,可從泵體頂端引水杯注入清水,也可用真空泵注水(開動真空泵,排除水泵及管內氣體在水充滿水泵的同時,起動水泵,打開閘閥,停止真空泵)。
3、開啟電動機(注意水泵的旋轉方向)。
4、當電動機正常運轉后,逐步開大閘閥,排澇混流泵維修,達到所要求的工況后,調節填料松緊。若水泵運轉,軸承溫度等都正常,則可繼續運行。
III. Starting
Sequence
1.Close the oulet
sluice valve.
2. Inject
water into pump to remove the air in water-in pipe and pump which can realized
by injecting clear water from the water diversion cup of the pump body end or
by vacuum pump(start the vacuum pump, remove the air from pump and pipes, start
the water pump when the pump is full of water, open the sluice valve,混流泵生產廠家, stop the
vacuum pump).
3. Start the
motor(pay more attention on the rotation direction of pump)
4. When the motor runs normally, turn up the
sluice valve gradually, adjust the tightness of padding when gettng to the
required working condition.If the pump runs well, the temperature of bearing is
normal, and it can run sequentially.
3、安裝基礎:要求土質堅實牢固。
4、水泵安裝時,廣安市混流泵,必須保證泵軸的水平位置。
5、進水管末端應浸入水平面以下一米左右,但須離開泥底半米左右。
6、水泵安裝好后,計算允許吸上高度和揚程,排澇混流泵供應商,在水位穩定的條件下,要求為規定數量值的0.8~1.2倍范圍,否則水泵不會正常運行
I.
Installation Principle
1. Installation
Height: Cidering the height according to the rainy season or dry season.The suction
vacuum
height can
not be higher than the adsorbing height.
2. Installation
Location:The location is better to close to the water source as p as
can.It should be not
only
keeping the safety but also shortening the water inlet pipe and reduce the
headloss
)注意事項:
1、用皮帶傳動時,兩皮帶輪必須對正且平等,否則易掉帶或出事故,傳動皮帶輪應有防護裝置,以保證安全。
2、進出水路的各連接法蘭盤間,應有膠墊,以防進氣,漏水。
3、出水管末端 能浸沉池內或盡量靠近水面,以避免揚程損失。
4、如不用底閥,進水管口淹沒水中時,應用鐵絲網罩或竹制網罩以防水草等雜物進入葉輪,影響水泵正常運轉。
企業: 泰安金石泵業有限公司
手機: 13605386905
電話: 0538-6202947
地址: 山東省泰安市泰山區南關路12號