【廣告】
5、水泵有雜音或振動
There is noise
in pump or the pump is vibrating
1、軸中心沒有對正
2、軸彎曲軸承磨損過大
3、葉輪平衡性差
4、地腳螺栓松動
5、裝置不當
6、葉輪局部阻塞
7、吸水高度太高、發生汽蝕
8、泵內掉進雜物
1.The axile center is not aligning
2.The axile is bend,大流量混流泵供應商, the bearing wears
much
3.The balance of impeller is not good
4.The foundation bolts are loose
5.The assembly is improper
6.Part of the impeller is blocked
7.The suction head is too high to produce
cavitation
8.There are sundries in pump.
1、找正
2、校正或更換軸承
3、進行靜平衡試驗和調整
4、擰緊
5、檢查機組
6、消除雜物
7、降低安裝位置減低安裝高度
8、清除雜物
1.Calibrate
2.Calibrate it or change the bearing
3.Do the static balancing test and adjust
it
4.Tighten it
5.Check the pump unit
6.Remove the sundries
7.Reduce the installation site to reduce
the installation height
8. Remove the sundries
4、耗用功率太大
The power
cumption is too large
1、轉速太高
2、傳動軸彎曲
3、填料壓得太緊
4、軸承磨損或損壞
5、葉輪和前蓋摩擦
6、皮帶太緊
1.The rotate speed is too high
2.The drive shaft is bend
3.The padding is too tight
4.The bearing is worn out
5.Impeller clashes the front cover
6.The belt is too tight
1、降低轉速
2、校直
3、擰松壓蓋螺栓或?qū)⑻盍先〕龃虮庖恍?/p>
4、更換軸承
5、調整葉輪端面軸向間隙
6、適應放松
1.Reduce the rotate speed
2.Straightening
3.Loose the cap blot or take our the
padding and make it more flat
4.Change the bearing
5.Ajust the end play of impeller end face
6.Loose the belt to suitable degree
三)密封裝置是由填料函、水封圈、填料壓蓋和鉛粉(或油浸)石棉盤根填料組成。其作用有:
1、啟動時防止空氣吸入泵內,起密封作用。
2、抽水時防止水從泵內過多的沿軸大量流出。
III. Sealing equipment is composed of stuffing box,廣西混流泵供應商,
water seal, packing gland,農業混流泵供應商,lead powder(or oil immersed)
asbestos
packing padding.Its use is as follows:
1. When
starting, stop the pump from sucking air and realize the sealing function.
2. When
drawing water, stop the water running out through the axle from pump.
企業: 泰安金石泵業有限公司
手機: 13605386905
電話: 0538-6202947
地址: 山東省泰安市泰山區南關路12號